I’m planning on building a new home server and was thinking about the possibility to use disc spanning to create matching disk sizes for a RAID array. I have 2x2TB drives and 4x4TB drives.

Comparison with RAID 5

4 x 4 TB drives

  • 1 RAID array
  • 12 TB total

4 x 4 TB drives & 2 x 2 TB drives

  • 2 RAID arrays
  • 14 TB total

5 x 4* TB drives

  • Several 4TB disks and 2 smaller disks spanned to produce a 4 TB block device
  • 16 TB total

I’m not actually planning on actually doing this because this setup will probably have all kinds of problems, however I do wonder, what would those problems be?

  • CouncilOfFriends@slrpnk.netEnglish
    3·
    5 months ago

    If you don’t need realtime parity, I’ve had no issues on my media server running mismatched drives pooled via MergerFS with SnapRAID doing scheduled parity.

  • catloaf@lemm.eeEnglish
    3·
    5 months ago

    What are you going to be running on these disks? I haven’t used zfs, maybe it supports mismatched sizes? Or maybe you could do one array with the 4s, another with the 2s, and use LVM to pool them together? Or just keep them separate and fill them up independently.

    • FrederikNJS@lemm.eeEnglish
      4·
      5 months ago

      ZFS doesn’t really support mismatched disks. In OP’s case it would behave as if it was 4x 2TB disks, making 4 TB of raw storage unusable, with 1 disk of parity that would yield 6TB of usable storage. In the future the 2x 2TB disks could be swapped with 4 TB disks, and then ZFS would make use of all the storage, yielding 12 TB of usable storage.

      BTRFS handles mismatched disks just fine, however it’s RAID5 and RAID6 modes are still partially broken. RAID1 works fine, but results in half the storage being used for parity, so this would again yield a total of 6TB usable with the current disks.

  • mlaga97@lemmy.mlaga97.spaceEnglish
    3·
    5 months ago

    I ran RAID-Z2 across 4x14TB and a (4+8)TB LVM LV for close to a year before finally swapping the (4+8)TB LV for a 5th 14TB drive for via zpool replace without issue. I did, however, make sure to use RAID-Z2 rather than Z1 to account for said shenanigans out of an abundance of caution and I would highly recommend doing the same. That is to say, the extra 2x2TB would be good additional parity, but I would only consider it as additional parity, not the only parity.

    Based on fairly unscientific testing from before and after, it did not appear to meaningfully affect performance.

  • Decronym@lemmy.decronym.xyzBEnglish
    2·
    5 months ago

    Acronyms, initialisms, abbreviations, contractions, and other phrases which expand to something larger, that I’ve seen in this thread:

    Fewer Letters More Letters
    LVM (Linux) Logical Volume Manager for filesystem mapping
    RAID Redundant Array of Independent Disks for mass storage
    ZFS Solaris/Linux filesystem focusing on data integrity

    3 acronyms in this thread; the most compressed thread commented on today has 17 acronyms.

    [Thread #788 for this sub, first seen 5th Jun 2024, 22:35] [FAQ] [Full list] [Contact] [Source code]

  • MalReynolds@slrpnk.netEnglish
    33·
    5 months ago

    If you’re doing weird shit, partition the 4TBs into 2x2TB, now you have 10x2TB. Or use unraid / mergerfs + SnapRaid.